Видео

Hey man, I have a 2024 RZR 1000xp with a light bar baja style that has 2 relays on the harness what do I do in this case to wire up these Amazon plugs on are pulse bar. Thanks :)

They need PulseBar Plugs that have the relay attached directly as one plug. no need for connecting wires,

thank you for the awesome video. it was/is/will be super helpful! love from maine.

Picked up a '24 RZR and learning a ton about this as I am adding several accessories. Here is some random info, I didn't even think to look into....fuses. This car has several different types of fuses; Primary Fuse Center (under the center arm rest) uses various MCASE fuses, with a 200A ZCASE fuse on the cable feeding the Pulse Bar. At the Pulse Bar, that 40A fuse is a JCASE fuse for direct protection on that bar. The switched ignition on the Pulse Bar has a 10A mini blade fuse which can be found in the Secondary Fuse Center next to the drivers knee; this is the "TERM BLK" fuse. Who in the world carries around these types of fuses, should one blow?? Now I do.....

Good stuff 👍🏻

🔥🔥 what psi r u running out there?

Very informative. I have had the same trouble. Thanks

I appreciated the video so much, I watched all the commercials. Thank you!

Your going to burn your house down

Dude you are terrible, learn how to don't give a wiring job,your terrible grade f.

I would just like to add that wrench is called a crow's foot. The rusty ball parts you found are for the float detent. Your blower lift cylinder should be connected to those two connections to allow the blower to float with no down pressure when that lever is fully moved forward. The downside of buying a used item is you have no idea how long will it last before the same thing happens again. But I would have done the same thing as everything Deere is very expensive. I likely would have tried to repair the assembly before I purchased another. Other than that, very helpful video.

thin im just getting an auxbeam when I add lights, having to buy a relay and an inline fuses when they are pre installed. and mounting it in a easier to get to location. The new 24 XP RZR its mounted in such a crap spot, and now I ahve a windshield installed, so roof has to come off to remove windshield, then the dash panel, and its mounted opposite of where you can see it.

I did something similar with a RIBU1C and our gas fireplace. Alexa smart plug powers the RIB and closes the millivolt contact to ignite. I removed the wall switch and added an automation so that once powered it shuts off after two hours. Works like a charm!

Were heading up there next week never road up there

Did you need a 24v transformer

Wheeling has become such a shit show...More money than brains...Everywhere

it doesn't need to be replaced with a new part when t has just been unused for years. minnesota equipment dealer in rogers mechanic told me the trick is to take the side covers off and use cleaning penetrating oil as it's just seized, like all rusty things heating stuff up helps, but really you don't need to do that with all the rubber seals in it, there are spring tensioned parts that will explode out after you take the cap bolts off so hold a finger over the cap and slowly let each come out and have another hand or parts bucket/tray right below to catch everything that springs out and look at the order of it all as you remove it. i disconnected the steering column lever and used some heavy handed persuasion with a 2 pound and a flat head round punch to get things moving before hitting it with the penetrating oil and then the lubricating oil and reconnecting the steering column handle lever and working it back and forth each way a couple hundred times until it felt as smooth as the working one before reassembling the spring valves and securing the cap covers. you only need to remove the cover of the stuck one, usually it is the top one the deere mechanics said goes unused for years as most every one just uses the up down function for the mower deck.

Thats awesome man! I didn’t even know they made little smart switches that can hook up to alexa, so my question is this will continue happening even though you have the rib relay installed to reset only, because the smart switch can only hold 5-6amps correct? The best way is for you to run its own circuit from the breaker with higher amps to your heater. Or am i missing something?thanks

You also may need a relay depending on the pulse relay style. If the constant power is always on (key on or off) a relay is needed to prevent un-wanted power consumption.

I like what you did here, but could you show me how to add the 5 prong rocker switch with the relay, and pulse bar. I am over thinking this cause I cant get it to work. Thanks Don

Can you please provide some more details about your wiring setup? From what is available in the video, it is totally unclear how this functions as a relay, and why a relay is necessary. It looks like you ran a switched circuit partially through a relay, which works because a switched circuit is all you needed to begin with: a smart switch to open the circuit the fireplace is on. I think you can pull this thing out and put it to work somewhere else.

I got some questions on this I’d like to ask trying to wire in a pulse bar and relays now

Outstandiing video. I broke the cap and lost the two ball bearings. I ordered a replacement spool valve for $129 from eBay. I moved the cap to the existing spool valve BUT did not understand placement of the two ball bearings. Now I do. I removed the cap, removed the side plugs, removed the springs, removed the ball bearings, cleaned everything, installed the caps and inserted the ball bearings and installed the side plugs. To you: thank you. It works perfectly now.

Did you have to charge the system when it was all back together?

👏👏👏👏

Very well explained.. nice workbench also😁

The 400 series John Deere tractors were made between 1992-2001.

How do you hardwire it?

I am doing same job, now, all ready ruined the replacement bought on ebay, cant remember how to reconnect chain link connecters to flat linkage and spool rods , you did not show how you connected the linkage under machine, I tried to apart the spool rods on new one and messed them up, any tips would be helpfull , thanks jim

It's safe to say the Pro XP got water in the belt, it's no coincidence you got stuck in water at that height. As an owner of the same machine, you should look at the belt exhaust, it's rather low but a fix is available from Dig Rig.

Mark says Only Polaris getting stuck!!😂😂

I did this repair a couple of Years ago. I can tell you it wasn't a fun job. But saved an enormous amount of Money, being paid to the Green Mafia (A.K.A. John Deere).

Link for relay: a.co/d/cW5CC4G

That looked like a lot of fun!!!

Love❤

I don´t understand the purpose of this switch. Ecoflow powerstations (I do also have one, but a smaller one), are able to receive and release power at the same time. So either solar from the converter and/or grid from the input side, and output the same time. It can be also used as an USV. The only important one would be, that the Ecoflow would be "built in" with the display and power on button visible from the outside every time. So something like a spare in the front of the storage door, which fits the size of the front panel of the ecoflow. And some doors for the inputs and outputs to connect and release, if needed. By the way: With the usage of solar, it could make sense to add some additional (car, truck, whatever) battery to charge this thing from the ecoflow as a backup, and get power of it, as needed. Because the ecoflow could work like this. For this, it would make sense to add a switch for to change input from solar to external battery, and, if needed, a second one for the 12V output to switch between external battery for to charge or additional usage in the camper.

Good stuff!!

Nice video! I love Black Mountain. It is in my top three trail systems for sure. I have the same machine too! The only difference is.....I ride mine fast and hard! I wasn't sure if ya'll were out there bird watching or riding! Lol! Just kid'n, love the video and be safe out there!

awesome quad....what are you running for GPS and bluetooth?

Where is this place?

Great video and all but you were not even going above 30mph. Please next add some speed because your content is amazing.

why does it look like you have Holeshots on your X MR? You get stuck so easy. Or did you put a snorkel on an X xc?

How do you get there, I tried to find that trail but cant

Are timers wireless or wired? If pump is in far corner downstairs and countdown timers are at the other end of the house upstairs, are you hardwiring them? The Insteon countdown timers were great before they discontinued them.

I thought people camping out on top of test hill were the worst but it is those camped at the bottom. Great video!

I love this video!